routing dengan protocol rip

untuk memperoleh file simulasi di atas dapat di download di sini

berikut perintah-perintah nya.

Router 0

Router>

Router>enable

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#interface fastEthernet 0/0

Router(config-if)#ip address 192.168.1.1 255.255.255.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#

Router(config)#interface serial 0/0/0

Router(config-if)#ip address 192.168.2.1 255.255.255.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router(config-if)#exit

Router(config)#

Router(config)#router rip

Router(config-router)#network 192.168.2.0

Router(config-router)#network 192.168.1.0

Router(config-router)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#copy running-config startup-config

Destination filename [startup-config]?

Building configuration...

[OK]

Router#

Router 1

Router>

Router>enable

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#interface fastEthernet 0/0

Router(config-if)#ip address 192.168.3.1 255.255.255.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#

Router(config)#interface serial 0/0/0

Router(config-if)#ip address 192.168.2.2 255.255.255.0

Router(config-if)#clock rate 9600

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router(config-if)#exit

Router(config)#

Router(config)#interface serial 0/1/0

Router(config-if)#ip address 192.168.4.1 255.255.255.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0, changed state to up

Router(config-if)#exit

Router(config)#

Router(config)#router rip

Router(config-router)#network 192.168.2.0

Router(config-router)#network 192.168.3.0

Router(config-router)#network 192.168.4.0

Router(config-router)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#copy running-config startup-config

Destination filename [startup-config]?

Building configuration...

[OK]

Router#

Router 2

Router>

Router>enable

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#interface fastEthernet 0/0

Router(config-if)#ip address 192.168.5.1 255.255.255.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#

Router(config)#interface serial 0/0/0

Router(config-if)#ip address 192.168.4.2 255.255.255.0

Router(config-if)#clock rate 9600

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router(config-if)#exit

Router(config)#

Router(config)#router rip

Router(config-router)#network 192.168.4.0

Router(config-router)#network 192.168.5.0

Router(config-router)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#copy running-config startup-config

Destination filename [startup-config]?

Building configuration...

[OK]

Router#

Pc 0

ip address 192.168.1.2

subnet mask 255.255.255.0

default gateway 192.168.1.1

Pc 1

ip address 192.168.3.2

subnet mask 255.255.255.0

default gateway 192.168.3.1

Pc 2

ip address 192.168.5.2

subnet mask 255.255.255.0

default gateway 192.168.5.1